Join Waitlist We will inform you when the product arrives in stock. Just leave your valid email address below.
Email Quantity We won't share your address with anybody else.
Product added to wishlist
View Wishlist

Free Ground Shipping on all orders over £80 (UK only)

BNF Micro FPV Racing Quad (DSM2)

Add to Wishlist

From: £66.75 £59.99

5.00 out of 5 based on 1 customer rating
(1 customer review)
1 review  |  Write a review

Micro FPV Racing Quad

F3 EVO Flight Controller with Native Spektrum DSM Receiver
Now DX6 (Spektrum)TX types , Not G2 or euro type.

175mAh 3.7V 25C / 50C 1S MyLipo MX

Added this great little MyLipo for half price

53 in stock

Colour propellers for 6mm motors Tiny Whoop

And a set of props half price

Clear

205mAh 3.7V 25C / 50C 1S Mylipo MX

Add these great MyLipos for extra flight time

Out of stock

Mylipo 205mAh HV 4.35V 25C / 50C MX

Go HV and feel the power
You will need the correct charger for HV lipo

20 in stock

43 in stock

SKU: Makerfire BNF (DSM) Spektrum Categories: ,

 Will not work with stock horizon tx from the inductrix range 

Features

  • 64mm motor spacing, four carefully-tuned electric ducted fans

  • Makerfire F3 EVO Brushed flight controller native with DSM receiver, fully programmable through Cleanflight/Betaflight

  • Compatible with Spektrum DX6, DX8, DX9, DX18 transmitter. Not compatable with new type euro tx from Horizon. 

  • 5.8G AIO 25mW camera, give you 10° camera angle

  • Special sauce edition motors, 17500Kv, 65,000 RPM@3.7v,up to 1.34A load current at 4.2V (direct drive)

  • 35C 200mAh 1S battery, 3 min 40 seconds flight time

Specifications

  • Wheelbase: 64mm

  • Weight: 22g (without battery)

  • Flight Controller: Makerfire F3 Brushed FC with DSM2 receiver

  • Motor: 6x15mm Coreless Brush Motor

  • Receiver: DSMX/DSM2 compatible native receiver

  • Camera and 5.8G Tx: AIO 520TVL 1/4 Inch Camera 25mW 40CH

  • Batterry: 3.7V 200mAh Lipo battery with Pico JST connector

  • Flight time: 3 min 40 seconds

 

 

Package Includes:

1 x Micro FPV quad
1 x 200mAh 3.7v Lipo battery

1 x Service card

 

Frequently Asked Questions

Due to the overwhelming response from the customers, we have put together this FAQ to answer the most commonly asked questions.This section will grow as more and more customers give us valuable feeedback and suggestions on how to improve the tuning.

Q: Can I enjoy it if i am a drone hobby beginner?

This is not a beginners quad.You will need a decent transmitter.

You will need to know how to use the program cleanflight/betaflight.

Most importantly,you should have 5.8G goggles to enjoy the FPV experience.

Q: Is this a complete RTF quad?

This is not complete RTF drone. You will need a transmitter to bind to it. Spektrum DX8 is recommended.

Q: I want more information about the brush flight controller.

F3 brushed flight controller with Native DSM receiver, support DSM2 protocol with 6 channel or above for this current version, compatible with Spektrum DX6, DX8, DX9, DX10, DX18, DX20 transmitter. NOTE: NOT G2 type

Q: What Flight Modes does it have?

The board runs the popular Cleanflight/Betaflight firmware that is fully customizable and includes several different modes: Auto-Level, Horizon (auto-leveling mode with ability to flip), and full manual (rate). You can also enable AirMode and be able to control the quad at any speed and attitude!


Manual (link)

PID's (Link) 

BetaFlight 3.0.1 rocks with the "MR. Steele" PIDs.

 

 

Binding & Flying Procedure DSM version

Supports all the Spectrum radio transmitter,like DX6/DX6i.

This is a high-quality Spektrum DSMX/DSM2 compatible receiver. It is not an official Spektrum receiver.

The Spektrum, DSMX and DSM2 brand is a trademark of Horizon Hobbies, USA.

Cleanflight GUI Set Up

CLI Tab:Go to CLI and type this in.

set motor_pwm_rate=4000
save

 

 

Ports Tab:Switch on Serial RX of UART2. And click the Save and Reboot button in the lower right corner.

Components

Configuration Tab:ESC/Motor Features, Switch on MOTOR_STOP(optional).

Components

Receiver Mode, choose RX_PPM;Serial Receiver Provider, choose SPEKTRUM1024.

And click the Save and Reboot button in the lower right corner.

 

Modes Tab:ARM,click Add Range.ANGLE,click Add Range.

And click the Save button in the lower right corner.

Components

 

 

Ed. note.

(There is a push-button under the battery compartment. Press this button whilst connecting the battery or USB cable; both work. A blue LED will flash very rapidly when the receiver is in bind mode. This is the 3rd most inner LED on the underside of the PCB. The other two are for the flight controller.

If you have problems binding change the TX to DSM2 / 22ms mode. Normally what you set on the TX is the desired mode and the TX+RX negotiate their capabilities and select a mutually compatible mode.

If you still have problems binding take the TX and walk to the other side of the room. This is a solution that Spektrum themselves recommend for some TX+RX firmware combinations. This seems to be the case between most DX8 and this quad.

The receiver outputs PPM signal.)

 

 

 

Why wont my quad arm? 

It has been the case on a few transmitters that the quad does not seem to arm. This could be due to the throttle not being quite at zero, and so the quad will not arm. 

Please check your RX Range if you can not arm your quad. Here is a great video explaing how to check and set your RX range.

An excellent info page here. (Look right down the bottom of the page)

 

 

Note : 

The F3 flight control board has a native Spektrum DSM2 receiver which works with any DSM2 compatible transmitters,

It also has support for external receivers like Makerfires ISky AC800 which will allow you to connect your Taranis transmitter

 

Note : the included USB charger is NOT to be used as a long term soloution for charging your lipos.
Never leave the lipo plugged in for longer than it takes to charge it.
We recomend you buy a proper lipo charger as soon as possible. 

Please follow and like us:

Colour propellers for 6mm motors Tiny Whoop

205mAh 3.7V 25C / 50C 1S Mylipo MX

Mylipo 205mAh HV 4.35V 25C / 50C MX

1 review for BNF Micro FPV Racing Quad (DSM2)

  1. 5 out of 5

    (verified owner)

    This is my first Tiny Whoop and the service has been awesome! My first one was faulty and Jem offered to replace it. The replacement has been working awesome with my Spektrum DX9!… 
    I would recommend this quad! It's much cheaper than the Blade Inductrix FPV that I was going to get originally… and I believe this one has better components!

     

    I will definitely order more batteries!

Only logged in customers who have purchased this product may leave a review.

100% of our customers only have praise for our prompt delivery and professional service, give us a try and check it out for yourself! ×
We'll endevour to get you back in the air, or into the air as quick as postally possible, our only limitation is the delivery service itself! ×
If you need to have a chat about anything micro quad related or you need to contact us for advice please drop us a line and we'll get it done! ×
This is a static CMS block edited from admin panel. You can insert any content here. ×